Search found 23 matches

by Jack Duren
Wed, Mar 15 2023, 12:24PM
Forum: eCabinet Systems Software
Topic: Toe board and notch
Replies: 2
Views: 2227

Toe board and notch

Trying to get the toe board and notch to line up to the face. Back and forth. I'm missing something.
toe board save2.jpg
by Jack Duren
Thu, Mar 09 2023, 11:44AM
Forum: eCabinet Systems Software
Topic: fin to wall toe board
Replies: 5
Views: 6700

Re: fin to wall toe board

Thx... Working out one problem at a time.

On to problem number two.
ToeBoard save1.jpg
by Jack Duren
Thu, Mar 09 2023, 11:20AM
Forum: eCabinet Systems Software
Topic: fin to wall toe board
Replies: 5
Views: 6700

Re: fin to wall toe board

think I'm getting it..
by Jack Duren
Thu, Mar 09 2023, 11:14AM
Forum: eCabinet Systems Software
Topic: fin to wall toe board
Replies: 5
Views: 6700

Re: fin to wall toe board

Not sure where you are seeing this option?
by Jack Duren
Wed, Mar 08 2023, 5:13PM
Forum: eCabinet Systems Software
Topic: fin to wall toe board
Replies: 5
Views: 6700

Re: fin to wall toe board

toe board save.jpg
by Jack Duren
Wed, Mar 08 2023, 5:07PM
Forum: eCabinet Systems Software
Topic: fin to wall toe board
Replies: 5
Views: 6700

fin to wall toe board

I have a finished left cabinet with a right wall end. I have a frame hangs over 1/2 on the wall end, but unable to extend the toe to match. Simple fix?
by Jack Duren
Tue, Apr 10 2007, 3:43PM
Forum: eCabinet Systems Software
Topic: Partitions and resizing
Replies: 2
Views: 2704

I sent it. Let me know if received...Jack
by Jack Duren
Tue, Apr 10 2007, 10:12AM
Forum: eCabinet Systems Software
Topic: Partitions and resizing
Replies: 2
Views: 2704

Partitions and resizing

Have a problem with resizing a cabinet and the partition showing up in the door opening. Is there a way to set the partition so it is always in the center of the mid stile?

I do a lot of full inset doors....Jack
by Jack Duren
Fri, Apr 06 2007, 10:47PM
Forum: eCabinet Systems Software
Topic: Is there an affordable laptop to run ecabinets?
Replies: 21
Views: 17289

I use a Dell 5100 2.8 Ghz without any problems.....Jack
by Jack Duren
Mon, Mar 19 2007, 9:38PM
Forum: eCabinet Systems Software
Topic: Partially opened doors & drawers
Replies: 4
Views: 3997

Thx for the replies and info. I'll have to give it a try.....Jack
by Jack Duren
Sun, Mar 18 2007, 10:42PM
Forum: eCabinet Systems Software
Topic: Partially opened doors & drawers
Replies: 4
Views: 3997

Partially opened doors & drawers

I know this has been mentioned and discussed as I have seen it while searching for other answers on eCabinets But cannot locate any info. How would I search the archieves for this?

THx....Jack
by Jack Duren
Wed, Mar 14 2007, 7:54PM
Forum: eCabinet Systems Software
Topic: Upper extended end issue
Replies: 17
Views: 13616

Opened the cabinet and looked at the settings. The deck is 52\". The cabinet is 52\". If the deck is 52\" this will make the cabinet 52 1/2 long. A 1/2 too long. For a 52\" cabinet the deck should be 51 1/2 (1/4 dado left of 3/4 finished end) and the top should be 51\" .The ...
by Jack Duren
Wed, Mar 14 2007, 6:40PM
Forum: eCabinet Systems Software
Topic: Upper extended end issue
Replies: 17
Views: 13616

Kerry I've downloaded the cabinet but it wont open. I can see the file on the desk top but wont open...Jack
by Jack Duren
Tue, Mar 13 2007, 7:32PM
Forum: eCabinet Systems Software
Topic: Upper extended end issue
Replies: 17
Views: 13616

Kerry this still does'nt work. Only readjusting the face frame. The cabinet is 52 1/2 wide and still makes the deck 52.5.....Jack
by Jack Duren
Sun, Mar 11 2007, 6:49PM
Forum: eCabinet Systems Software
Topic: Upper extended end issue
Replies: 17
Views: 13616

Ok I'm back to solving this problem. Its a typical Kansas City construction technique.

So what do the senior members say? Can or cant?......Jack