Search found 113 matches
- Fri, Feb 22 2013, 7:41PM
- Forum: eCabinet Systems Software
- Topic: raise the deck
- Replies: 1
- Views: 2648
raise the deck
hey All, I have some cabinets that are using inset doors, the customer would like for the 3/4" deck to be 1/4" above the 2" bottom rail so the door will have a stop. I thought it would be a simple change to the decks bottom inset of 1.25" to 1.5" but that does not work. Any ...
- Tue, Jan 08 2013, 11:04AM
- Forum: eCabinet Systems Software
- Topic: Beaded face Frames
- Replies: 2
- Views: 5790
Beaded face Frames
Is there anyway to show beaded face frames with inset doors??
Thanks,
Chris
Thanks,
Chris
- Sun, Dec 30 2012, 11:22AM
- Forum: eCabinet Systems Software
- Topic: End of Fly cut Code
- Replies: 3
- Views: 5181
Re: End of Fly cut Code
Hey Brian, yea I was a little concerned as I just don't have the experience with writing code. So I am looking at Ecab generated footers and working through my old class book. I have been running this same flycut that the Thermowood rep wrote for me years ago when I had the router installed. I shoul...
- Sat, Dec 29 2012, 2:28PM
- Forum: eCabinet Systems Software
- Topic: End of Fly cut Code
- Replies: 3
- Views: 5181
End of Fly cut Code
hey All, Well I have put up with this for years now and i finally got the chance to fix it but I just need a little advice. My fly cut has always just gone "OUT OF BOUNDS" at the end of it's run, I have to emerg stop and reset to get it home. So now I would like it to return home as it sho...
- Tue, Sep 11 2012, 4:00PM
- Forum: eCabinet Systems Software
- Topic: angled top
- Replies: 5
- Views: 6901
Re: angled top
Make your top a display panel. thats the only way I have been able to rotate cabinet parts.
- Mon, Jun 18 2012, 9:32AM
- Forum: eCabinet Systems Software
- Topic: Cutting Aluminum
- Replies: 3
- Views: 4415
Re: Cutting Aluminum
LOL Yeah I will never forget the first time I cut a piece of aluminum on the table saw without a face shield! Ya learn fast... i dunno about the WD40 I have found that working my mill and running out of cutting fluid I had grabbed a can of WD40 used it and ruined the end mill... Just does not seem t...
- Sun, Jun 17 2012, 12:51PM
- Forum: eCabinet Systems Software
- Topic: Cutting Aluminum
- Replies: 3
- Views: 4415
Cutting Aluminum
Not sure if this is the right place for this but... have any of you guys tried cutting aluminum sheet? maybe about .060" material. I use Bobcad software from time to time allowing me to easily create some nice stuff for the race car. Just been really hesitant about using the thermwood router as...
- Mon, Jun 11 2012, 3:07PM
- Forum: eCabinet Systems Software
- Topic: drawer box front for pull-outs
- Replies: 22
- Views: 21080
Re: drawer box front for pull-outs
didn't see the last post.....
Thanks again,
Chris
Thanks again,
Chris
- Mon, Jun 11 2012, 3:06PM
- Forum: eCabinet Systems Software
- Topic: drawer box front for pull-outs
- Replies: 22
- Views: 21080
Re: drawer box front for pull-outs
Seems to nest ok. I will run it later today. Don't understand why this changed? I am not sure if this was checked in the past??
Thanks,
Chris
Thanks,
Chris
- Mon, Jun 11 2012, 2:30PM
- Forum: eCabinet Systems Software
- Topic: drawer box front for pull-outs
- Replies: 22
- Views: 21080
Re: drawer box front for pull-outs
Changed tool dia. to .25" Same problem.
Chris
Chris
- Mon, Jun 11 2012, 1:37PM
- Forum: eCabinet Systems Software
- Topic: drawer box front for pull-outs
- Replies: 22
- Views: 21080
Re: drawer box front for pull-outs
Hi Joe,
I can try the bit dia. size soon, right now it is set at .235 with time left. as far as the arc dia. It's a 3 point arc. Radius of the arc... Well regrettably the line drawing editor doesn't recognize a drawer box to pull measurements off of.
Chris
I can try the bit dia. size soon, right now it is set at .235 with time left. as far as the arc dia. It's a 3 point arc. Radius of the arc... Well regrettably the line drawing editor doesn't recognize a drawer box to pull measurements off of.
Chris
- Mon, Jun 11 2012, 11:55AM
- Forum: eCabinet Systems Software
- Topic: drawer box front for pull-outs
- Replies: 22
- Views: 21080
- Mon, Jun 11 2012, 11:50AM
- Forum: eCabinet Systems Software
- Topic: drawer box front for pull-outs
- Replies: 22
- Views: 21080
Re: drawer box front for pull-outs
Well it wont allow the .cab extension
- Mon, Jun 11 2012, 11:49AM
- Forum: eCabinet Systems Software
- Topic: drawer box front for pull-outs
- Replies: 22
- Views: 21080
Re: drawer box front for pull-outs
$&*(^*)_(@#.... MONDAY MORNING!!!
Here Ya Go.
Here Ya Go.
- Mon, Jun 11 2012, 11:45AM
- Forum: eCabinet Systems Software
- Topic: drawer box front for pull-outs
- Replies: 22
- Views: 21080
Re: drawer box front for pull-outs
???? << Go to control nesting and load the twd you are having problem with. the go to file->Export>>>???
Okay, Load file, bottom of screen F5 (File) there is no export button? I can save a file (F2) but it is the CNC file.
Okay, Load file, bottom of screen F5 (File) there is no export button? I can save a file (F2) but it is the CNC file.