Range Hoods and Valances

Moderators: Jason Susnjara, Clint Buechlein

Post Reply
andy Schermerhorn
New Member
Posts: 6
Joined: Tue, May 18 2010, 11:36AM
Company Name: precision built

Range Hoods and Valances

Post by andy Schermerhorn »

Hello I am new to eCabinets and have some questions. I need to design a range hood and valance like the ones that conestoga sells. What is the best way of doing this? The range hood I tried to make as an assembly then attach the different parts together to get the desired effect, but was not able to do so.Any input here would be great. Mainly having a problem with the angled parts of the hood.
Thanks
George Davidson
eCabinets Beta Tester
Posts: 1585
Joined: Tue, May 17 2005, 1:16PM
Location: Norwood Pa.

Re: Range Hoods and Valances

Post by George Davidson »

Hi Andy
If you put in Range Hood in Searh on the top of page. You will get some range hoods.
Do you have a picture of the one you want
andy Schermerhorn
New Member
Posts: 6
Joined: Tue, May 18 2010, 11:36AM
Company Name: precision built

Re: Range Hoods and Valances

Post by andy Schermerhorn »

What I am trying to create is a range hood with slanted front that starts at 12"deep at the top and goes to 18" deep at the bottom with three raised panels on the angled face. Below the angled face is a ledge like a mantle with trim under it, and a curved raised panel valance below that. If this makes any sense to anyone besides me, I dont know. The cabinet needs to be 42" w x 32"h x 20" deep overall. Not sure how far off the top of the range the hood needs to be, at 32"h the panel would be 28" off the range.
George Davidson
eCabinets Beta Tester
Posts: 1585
Joined: Tue, May 17 2005, 1:16PM
Location: Norwood Pa.

Re: Range Hoods and Valances

Post by George Davidson »

I am not sure if this is what you are looking for.Before I do any more to it
Attachments
Hood-t.jpg
Hood-t.jpg (20.16 KiB) Viewed 29808 times
Range Hood 42 W x 32 H x 20 D.jpg
Range Hood 42 W x 32 H x 20 D.jpg (42.59 KiB) Viewed 29453 times
andy Schermerhorn
New Member
Posts: 6
Joined: Tue, May 18 2010, 11:36AM
Company Name: precision built

Re: Range Hoods and Valances

Post by andy Schermerhorn »

This is close, thank you for helping me I have more problems then I can handle. The sides of it are flat not angled, to fit between to cabinets. The only angle is the front where the paneling would be. Thank you for the help, I take it that that did not come from ecab.
George Davidson
eCabinets Beta Tester
Posts: 1585
Joined: Tue, May 17 2005, 1:16PM
Location: Norwood Pa.

Re: Range Hoods and Valances

Post by George Davidson »

Here is one I made before
42" x 24" x 19"
Attachments
42 x 24 x 19 D.esa
(554.02 KiB) Downloaded 1299 times
42 x 24 x 19 D.jpg
42 x 24 x 19 D.jpg (16.51 KiB) Viewed 29803 times
andy Schermerhorn
New Member
Posts: 6
Joined: Tue, May 18 2010, 11:36AM
Company Name: precision built

Re: Range Hoods and Valances

Post by andy Schermerhorn »

That is what I need thank you. One more question so I get this right, I take that esa file and download it to the assemblies library?
George Davidson
eCabinets Beta Tester
Posts: 1585
Joined: Tue, May 17 2005, 1:16PM
Location: Norwood Pa.

Re: Range Hoods and Valances

Post by George Davidson »

Yes I put it in a folder and then assemblies library
Lubert Willis
New Member
Posts: 1
Joined: Tue, Apr 17 2012, 7:37AM
Company Name: Precision Greenwood
Country: UNITED STATES

Re: Range Hoods and Valances

Post by Lubert Willis »

George Davidson wrote:I am not sure if this is what you are looking for.Before I do any more to it
Thank you George. This is what I was looking for!
This is great website where you will find all kinds of best range hoods.
George Davidson
eCabinets Beta Tester
Posts: 1585
Joined: Tue, May 17 2005, 1:16PM
Location: Norwood Pa.

Re: Range Hoods and Valances

Post by George Davidson »

Hi Lubert
OK
Can you put trim on it
Post Reply