5.2 build 3 problems

jerry johnson · Post by **jerry johnson** » Tue, Nov 25 2008, 4:36PM

I loaded 5.2 build 3 and am having a lot of problems. In the LDE I cannot go from page to page, when I take a cabinet into any of the editors the face frame and doors are all there and not transparent so I cannot see the inside of the cabinet to move partitions or shelves, modify or add drawers etc.. Also, I am getting all kinds of holes for drawer slides in all kinds of wierd places. HELP!!

Thanks!

Leo Graywacz · Post by **Leo Graywacz** » Tue, Nov 25 2008, 4:56PM

I am having a problem with the LDE also. I bring the drawing into the LDE and if I change the page it is blank, if I go back to the page I just brought in it is now blank.

I am not having the problem in the other editors. When I first upgraded I had it, I just re started the program and it went away. Just checked again and it is not happening, still good. But the LDE blank pages problem is still happening.

Jean G Voyer · Post by **Jean G Voyer** » Tue, Nov 25 2008, 5:54PM

I have the same problem with the LDE with blank pages. But I tried to delete a page and it reappeared asking me if I wanted to do it or not. Until that everything is blank.

Leo Graywacz · Post by **Leo Graywacz** » Tue, Nov 25 2008, 6:07PM

I can confirm that it comes back when you go to delete it. But it'll disappear again when you switch pages. Inconvienient, but workable for now.

Walker T Scott · Post by **Walker T Scott** » Wed, Nov 26 2008, 7:27AM

Jerry

Could you attach the job and will take a look at it.

Leo and Jean

Im getting the same thing and have passes this on to the programmers.

Thanks

Walker T Scott · Post by **Walker T Scott** » Wed, Nov 26 2008, 7:38AM

Leo and Jean

Here’s an easer work around minimize then maximize the ecabinets window. This should bring every thing back.

Joe Dusel · Post by **Joe Dusel** » Thu, Nov 27 2008, 11:12AM

I saw another interesting problem last night on a system using Vista. For some reason the eCabs software would not recognize any of the directories in the Cabinets folder when using the Cabinet/Assembly Editor. It recognized the Assemblies directories. I checked that the directories and files were there using Explorer. I then copied the Cabinets directory into a backup directory and did a Restore from it. The Cabinets directories then showed up again. Very strange...

Joe

jerry johnson · Post by **jerry johnson** » Fri, Nov 28 2008, 11:58AM

I ran "restore my files" and all seems to be well.

Leo Graywacz · Post by **Leo Graywacz** » Mon, Dec 01 2008, 9:42PM

Mine just seemed to sort itself out. Seems to work fine.....for now.

Leo Graywacz · Post by **Leo Graywacz** » Wed, Dec 03 2008, 12:20PM

OK I have a new one. Same place, LDE. I took a wall into the LDE and it showed me the backside of the wall. It took me a minute to figure out what this square was that was on the screen. I had to rotate it 180* to get the view that I wanted and should have been shown. Nothing critical, just another weird bug. My wall is facing the correct way, I tried reversing the build, but it just screwed everything up.

Walker T Scott · Post by **Walker T Scott** » Wed, Dec 03 2008, 1:10PM

Leo

Are you taking a reverse build wall to elevation view then taking it to the LDE? If so this is a known issue, if this is not what you are doing could you elaborate a little more of what you are doing.
Thanks

Leo Graywacz · Post by **Leo Graywacz** » Wed, Dec 03 2008, 2:20PM

This is not a reverse built wall. I go from the room editor into the single wall display in the room editor, wall #2 in my case. Then I choose the LDE icon and it gives me a series of choices and I choose take wall into LDE. When it takes the wall it is showing the backside of it which is blank. I have to rotate it 180* to get to the correct side. If this is a known problem I apologize for bringing it up again, it is a new problem to me and I don't recall seeing it on the forum. Thanks for the help.
If you need the file I can send it up.
Leo

Walker T Scott · Post by **Walker T Scott** » Wed, Dec 03 2008, 2:29PM

Could you attach the job and ill take a look and pass it along to the programmers.
Thanks

Leo Graywacz · Post by **Leo Graywacz** » Wed, Dec 03 2008, 2:43PM

Can't get it to uplad as an attachement. What is the email address please.

Daniel Menard · Post by **Daniel Menard** » Wed, Dec 03 2008, 3:12PM

We have a client that has noticed since the update that doors size are not setup to 1/64" .
This is trowing his guys off when making or ordering doors.
I am assuming that they are setup in their preferences to inches and fractions.

As anyone seen this?

Thermwood / eCabinet Systems

5.2 build 3 problems

5.2 build 3 problems

Re: 5.2 build 3 problems

Re: 5.2 build 3 problems

Re: 5.2 build 3 problems

Re: 5.2 build 3 problems

Re: 5.2 build 3 problems

Re: 5.2 build 3 problems

Re: 5.2 build 3 problems

Re: 5.2 build 3 problems

Re: 5.2 build 3 problems

Re: 5.2 build 3 problems

Re: 5.2 build 3 problems

Re: 5.2 build 3 problems

Re: 5.2 build 3 problems

Re: 5.2 build 3 problems