drawer box front for pull-outs

Chris B Campbell · Post by **Chris B Campbell** » Sat, Jun 02 2012, 5:41PM

Anyone having a problem in CN with the fronts of pull-out type drawers? (Pantry) We put a 3 point arch in the top of the front panel for a finger pull kind-a-look never had a problem, now CN shows a full circle... of course it goes off the table so were getting an X axis out of bounds?
Anyone else get this
Thanks chris

JohnLashuay · Post by **JohnLashuay** » Mon, Jun 04 2012, 11:55AM

Hi Chris, I haven't seen anything like this.

Can you post the cabinet?

-John

Chris B Campbell · Post by **Chris B Campbell** » Thu, Jun 07 2012, 6:37PM

Here is what I get after Nesting.
Chris

Rick Deskins · Post by **Rick Deskins** » Fri, Jun 08 2012, 8:39AM

Can you post the cabinet file this twd was made with?

Thanks

Chris B Campbell · Post by **Chris B Campbell** » Sat, Jun 09 2012, 1:09PM

Well I wish I could. I tried to upload the CNC File and the TWD file but these Extensions are not allowed??

Chris

Josh Rayburn · Post by **Josh Rayburn** » Mon, Jun 11 2012, 6:28AM

Chris,
You can change the extentions to .txt and post them or zip them then post.
jnr

Rick Deskins · Post by **Rick Deskins** » Mon, Jun 11 2012, 7:15AM

Chris,
We really need the ecabinets file. The twd/cnc files will show the problem, but it will not helps us tell you why you have the problem or how you might be able to fix it. Please post the ecabinet file.

Thanks,
Rick

Chris B Campbell · Post by **Chris B Campbell** » Mon, Jun 11 2012, 10:07AM

I thought ecabinets file was a TWD created by ecabinets? So I am not sure what or how I get you what you need.

Chris

Rick Deskins · Post by **Rick Deskins** » Mon, Jun 11 2012, 10:26AM

I need either the ecabinets job file (ESJ), cabinet file (HSF), or asssembly file (ESA) that was used to create the twd file.

Chris B Campbell · Post by **Chris B Campbell** » Mon, Jun 11 2012, 10:40AM

Hope this works

Rick Deskins · Post by **Rick Deskins** » Mon, Jun 11 2012, 10:52AM

Well, I tested your file going out to control nesting and all worked for me. So, there must be a setting on your control nesting that would produce this. I will need to get the export from your control nesting. Go to control nesting and load the twd you are having problem with. the go to file->Export and save off the export file. It will be a *.cab file. Then post that and hopefully we can find the root of your problem.

Chris B Campbell · Post by **Chris B Campbell** » Mon, Jun 11 2012, 11:45AM

???? << Go to control nesting and load the twd you are having problem with. the go to file->Export>>>???
Okay, Load file, bottom of screen F5 (File) there is no export button? I can save a file (F2) but it is the CNC file.

Chris B Campbell · Post by **Chris B Campbell** » Mon, Jun 11 2012, 11:49AM

$&*(^*)_(@#.... MONDAY MORNING!!!

Here Ya Go.

Chris B Campbell · Post by **Chris B Campbell** » Mon, Jun 11 2012, 11:50AM

Well it wont allow the .cab extension

Rick Deskins · Post by **Rick Deskins** » Mon, Jun 11 2012, 11:52AM

Can you email the cab file to cabinets@thermwood.com?

Thermwood / eCabinet Systems

drawer box front for pull-outs

drawer box front for pull-outs

Re: drawer box front for pull-outs

Re: drawer box front for pull-outs

Re: drawer box front for pull-outs

Re: drawer box front for pull-outs

Re: drawer box front for pull-outs

Re: drawer box front for pull-outs

Re: drawer box front for pull-outs

Re: drawer box front for pull-outs

Re: drawer box front for pull-outs

Re: drawer box front for pull-outs

Re: drawer box front for pull-outs

Re: drawer box front for pull-outs

Re: drawer box front for pull-outs

Re: drawer box front for pull-outs