Search found 274 matches

by Joe Soto
Wed, Jul 10 2019, 10:31AM
Forum: eCabinet Systems Software
Topic: Colored symbols on labels
Replies: 62
Views: 4606

Re: Colored symbols on labels

Thanks Clint, works good.

Tommy, FYI. Label cabinet numbers will not match actual cabinet numbers if you change the quantities at the control or have multiples of the same cabinet from a batch either.
by Joe Soto
Mon, Jul 08 2019, 9:27AM
Forum: eCabinet Systems Software
Topic: Colored symbols on labels
Replies: 62
Views: 4606

Re: Colored symbols on labels

My scanner reads it fine. The actual recut ID number is right at or slightly off the bottom edge of the label. But that might be a tracking problem with my printer.
by Joe Soto
Wed, Jul 03 2019, 1:09PM
Forum: eCabinet Systems Software
Topic: Colored symbols on labels
Replies: 62
Views: 4606

Re: Colored symbols on labels

That's a lot better Clint.
by Joe Soto
Wed, Jul 03 2019, 8:53AM
Forum: eCabinet Systems Software
Topic: Colored symbols on labels
Replies: 62
Views: 4606

Re: Colored symbols on labels

Works for me with DYMO 400 Turbo. Cabinet number could be larger but this works.
by Joe Soto
Wed, Jun 12 2019, 10:35AM
Forum: Thermwood 3-Axis Machinery
Topic: Teach Line Issue
Replies: 0
Views: 270

Teach Line Issue

In CNC View, type T,M,L Line Teach opens Cursor is in axis box, type 1,enter Cursor moves to Distance box, type 10(or any number) ,F11 or F12 no movement. Same with step plus and minus buttons they turn blue but no motion. MDI move is checked. F10 or undo teach returns to CNC view. Type T,M,L, 1 ent...
by Joe Soto
Fri, Jun 07 2019, 8:20AM
Forum: eCabinet Systems Software
Topic: Colored symbols on labels
Replies: 62
Views: 4606

Re: Colored symbols on labels

Why not just use the cabinet number already assigned by eCabs? A big font. Its already there on the cutlist, drawings, on the controller, even the buy list. Need to recut a deck for cabinet 23? Open the .twd scroll down to cab #23 and select the part. It would be helpful if we could renumber the cab...
by Joe Soto
Fri, May 31 2019, 12:42PM
Forum: Thermwood 3-Axis Machinery
Topic: Dado/pocket ramp in setting
Replies: 0
Views: 443

Dado/pocket ramp in setting

Is there a way to control where a dado or pocket ramp starts? I know how to set a start point with a .dxf but I have some parts created in eCabs with pockets that Cn wants to start the ramp on the shortest side. I have my dado pre ramp set at .01" and length at 4" with a speed of 40 ipm so...
by Joe Soto
Tue, May 14 2019, 1:25PM
Forum: Thermwood 3-Axis Machinery
Topic: CN v6.11 manual nest crash
Replies: 5
Views: 698

CN v6.11 manual nest crash

Any time I manually nest and end up with an empty sheet THM crashes when I write cnc. Pop up says empty sheets will be removed and sheets renumbered. Screen grays out and after a few minutes says software has stopped and must be restarted. As long as I leave one part on every sheet it writes correct...
by Joe Soto
Fri, Apr 19 2019, 8:33AM
Forum: eCabinet Systems Software
Topic: Error message lacking info
Replies: 2
Views: 835

Re: Error message lacking info

Same issue in the change materials in the room area. An error saying a constraint can't be applied and will be removed or a locked opening wont allow the change. No idea as to what part or cabinet. Probably more annoying is when that dialog pops up, it stops working until you hit ok. Sometimes chang...
by Joe Soto
Thu, Feb 07 2019, 2:11PM
Forum: eCabinet Systems Software
Topic: corner cabinet toe kick
Replies: 4
Views: 1244

Re: corner cabinet toe kick

Got it, removed left end part editor cuts and reapplied them. All is well. Thanks
by Joe Soto
Thu, Feb 07 2019, 1:38PM
Forum: eCabinet Systems Software
Topic: corner cabinet toe kick
Replies: 4
Views: 1244

Re: corner cabinet toe kick

That's the way it came off the router too but I need the toe to be flush with the notch.
by Joe Soto
Wed, Feb 06 2019, 5:23PM
Forum: eCabinet Systems Software
Topic: corner cabinet toe kick
Replies: 4
Views: 1244

corner cabinet toe kick

toe kick .jpg I can not figure out why the toe kick notch is 1/4" shorter on this side. I've used this same cabinet for several years without a problem. I cut this cabinet today and both ends cut like this but Ecabs only shows it on the left. The only recent changes were I added some screw hol...
by Joe Soto
Mon, Oct 08 2018, 9:50AM
Forum: eCabinet Systems Software
Topic: Carvings
Replies: 1
Views: 977

Re: Carvings

Here you go Carmen.
http://www.ecabinetsystems.com/ecabinet ... ograms.htm
There is an HSF file, which can be loaded into eCabinets.
Joe
by Joe Soto
Thu, Aug 02 2018, 10:03AM
Forum: Thermwood 3-Axis Machinery
Topic: Manual Nesting issues, etc...
Replies: 8
Views: 2973

Re: Manual Nesting issues, etc...

Same problem here, mine stalls when I click the calculate off-fall button. Even if I don't move anything in the nest.
by Joe Soto
Tue, Jul 24 2018, 10:06AM
Forum: eCabinet Systems Software
Topic: Can't have 2 faceframe thickness materials?
Replies: 15
Views: 4737

Re: Can't have 2 faceframe thickness materials?

Try this work around. Design your cabinet with the thick stiles, delete top bottom and mid rails. On page 2 of face frames change add mid rail to your thinner thickness material and add them to the cabinet to replace the rails you deleted.
2 thickness frame.JPG
2 thickness frame.JPG (12.54 KiB) Viewed 3822 times

Go to advanced search