Search found 539 matches

by Rick Deskins
Fri, Jun 22 2007, 10:20AM
Forum: eCabinet Systems Software
Topic: Cut lists
Replies: 8
Views: 2148

it might be a metric issue. if you change to inches, does it calculate it correctly?
by Rick Deskins
Thu, Jun 21 2007, 3:17PM
Forum: eCabinet Systems Software
Topic: Virtual PC
Replies: 23
Views: 8202

Multiple processors do not help ecabinet systems, but it will help out if you like to run multiple programs at the same time. Ecabinet Systems can run on processor, while the other apps run on the other. Just a thought.
by Rick Deskins
Wed, Jun 13 2007, 9:27AM
Forum: eCabinet Systems Software
Topic: can't load drawers
Replies: 7
Views: 2171

I looked a little more closely at the first file. It could have been saved off in the drawer box desinger, however if it was it is now a corrupt file. It has its geometry, but it is missing key hoops segments with your drawer box data. I would delete the file and remake it from the standard drawer b...
by Rick Deskins
Wed, Jun 13 2007, 8:58AM
Forum: eCabinet Systems Software
Topic: can't load drawers
Replies: 7
Views: 2171

Both these files are cabinet files, not actual drawer box files. They load just fine in the cabinet editor as cabinets. You can only load drawer box files in the drawer box desinger that are saved off from the drawer box designer. I understand what you are trying to do, work \"outside the box\&...
by Rick Deskins
Wed, Jun 13 2007, 8:25AM
Forum: eCabinet Systems Software
Topic: can't load drawers
Replies: 7
Views: 2171

Sounds like the drawer box file is corrupt. Can you post one that gives you the error message? Can you still load the standard drawer box file?
by Rick Deskins
Wed, Jun 13 2007, 7:23AM
Forum: eCabinet Systems Software
Topic: error message
Replies: 5
Views: 3140

Looks like the update file is corrupt. Please download and install this update.

http://downloads.thermwood.com/eCabinet ... Build3.exe
by Rick Deskins
Wed, Jun 06 2007, 9:08PM
Forum: eCabinet Systems Software
Topic: 5 piece door construction method
Replies: 1
Views: 1143

Have you seen our 5 piece door program?

http://www.thermwood.com/twood_site/pag ... manual.pdf
by Rick Deskins
Thu, May 24 2007, 9:33PM
Forum: eCabinet Systems Software
Topic: Edge Banding
Replies: 9
Views: 3069

Definitely a bug. However, for now you can right click in the main area and set the Front Construction of each Partition to Butt again. Then go to edge banding and everything will be good. The bug is in the partition construction settings. so if you change the construction setting of the partition i...
by Rick Deskins
Tue, May 22 2007, 2:26PM
Forum: eCabinet Systems Software
Topic: Need some Help PLEASE!
Replies: 3
Views: 1519

Re:

You made a tool to make that shape, Im going to be running them on the thermwood, just cos the tool was made to the shape do i need to have a tool that shape? Or can i do it with a bull nose cutter? Kinda sounds like a job profile modeler could do. http://www.thermwood.com/twood_site/pages_2_8_05/p...
by Rick Deskins
Fri, May 18 2007, 2:21PM
Forum: eCabinet Systems Software
Topic: I can not Batch anything
Replies: 3
Views: 1109

Sounds like your missing this file. C:\\Program Files\\Thermwood\\eCabinet Systems\\ff.twt
by Rick Deskins
Fri, May 18 2007, 1:13PM
Forum: eCabinet Systems Software
Topic: No Text
Replies: 8
Views: 3378

Ok. i looked a little more into it. If I delete my page, I get a error message when loading ecabinets. You do not. So, I checked my internet settings. After disabling a couple multimedia options, I was able to get the same results as you. So, could you please check you IE settings. Open IE, got to T...
by Rick Deskins
Fri, May 18 2007, 12:21PM
Forum: eCabinet Systems Software
Topic: No Text
Replies: 8
Views: 3378

ok. First try this. go to you web browser and enter \"C:\\Program Files\\Thermwood\\eCabinet Systems\\html\\animated_ecab_greeting.htm\" in the address bar. It should look like the jgp below. If it dont, you need to uninstall and reinstall the patch b3. This file is not in the orginial ins...
by Rick Deskins
Fri, May 18 2007, 9:43AM
Forum: eCabinet Systems Software
Topic: No Text
Replies: 8
Views: 3378

Sounds like your HTML directory is missing some files. Can you check in your ecabinets directory and look to see if you have Html\\animated_ecab_greeting.htm file? If the file is missing, you might have to repair the ecabinets setup and rerun the 5.1 b3 patch. If the file is there, then you might ha...
by Rick Deskins
Mon, May 14 2007, 8:38AM
Forum: eCabinet Systems Software
Topic: problem placing Cabinets
Replies: 6
Views: 2078

This is a bug when you change the mount height via the Change Size button in Place Items Dialog. If you change the mount height in the Define Standard Dimensions in Setting/Preferences, it will work correctly.
by Rick Deskins
Thu, May 10 2007, 2:39PM
Forum: eCabinet Systems Software
Topic: I don't want to miss a thing!
Replies: 5
Views: 2397

If you are in the cabinet editor or room and select the cabinet, you can press ctrl-shift-y to see the version info of the cabinet.

Go to advanced search