Search found 137 matches

by Gerry A Brown
Tue, Sep 23 2014, 12:45PM
Forum: Thermwood 3-Axis Machinery
Topic: Arcs Post P problems
Replies: 7
Views: 5297

Re: Arcs Post P problems

Hi Brad,

Thanks that is greatly appreciated.

Gerry :beer:
by Gerry A Brown
Tue, Sep 23 2014, 10:52AM
Forum: Thermwood 3-Axis Machinery
Topic: Arcs Post P problems
Replies: 7
Views: 5297

Re: Arcs Post P problems

Hi,
I will attempt to get it changed to incremental.
Thanks everyone,
Gerry
by Gerry A Brown
Mon, Sep 22 2014, 3:18PM
Forum: Thermwood 3-Axis Machinery
Topic: Arcs Post P problems
Replies: 7
Views: 5297

Re: Arcs Post P problems

Hi,

I should have mentioned we are running this on a 2007 CS45 with 6.1.6.5 control.

Thanks,
Gerry
by Gerry A Brown
Mon, Sep 22 2014, 11:53AM
Forum: Thermwood 3-Axis Machinery
Topic: Arcs Post P problems
Replies: 7
Views: 5297

Arcs Post P problems

Hello everyone, I am trying to get a Post P working that outputs Arcs but the router seems to cut all over the place when I run the code that is produced. Could some one please take a look at the code and see what is wrong with it. I have attached the code and the Post P that produced it. Thanks, Ge...
by Gerry A Brown
Sat, Sep 13 2014, 9:35AM
Forum: Thermwood 3-Axis Machinery
Topic: cuts the wrong size
Replies: 8
Views: 4636

Re: cuts the wrong size

Hi, I have worked through this trying all the suggestions. I get good results doing conventional feed with the G07F0 code. I have modified the Post P to insert this command and it all seems to work well. I have not got the Post P to output arcs yet but will pursue that as time permits. Thanks to eve...
by Gerry A Brown
Sun, Aug 31 2014, 7:13AM
Forum: eCabinet Systems Software
Topic: dowels
Replies: 10
Views: 4742

Re: dowels

Hi Scott, It has been a while since I tried but I did try to use the KD option to do this. I think it allows for a given number of fasteners and max spacing. We have a pattern set up for the common depths we use and just use the boring machine to do the vertical boring on the rest of them. It is a s...
by Gerry A Brown
Sat, Aug 30 2014, 7:28AM
Forum: eCabinet Systems Software
Topic: dowels
Replies: 10
Views: 4742

Re: dowels

Kerry,

I would be interested in any solutions you might have for this problem. Would you be willing to share your solution on the forum?

Thanks,
Gerry
by Gerry A Brown
Tue, Aug 26 2014, 8:56AM
Forum: eCabinet Systems Software
Topic: dowels
Replies: 10
Views: 4742

Re: dowels

Hi, We use both doweled & dowel & confirmat. Ecabinets does not support 32mm dowel drilling but you can make it work. It would be great if there was an option to add 32mm hole pattern to sides & patricians then go in and delete the holes you don't need. I think this has been on the to do...
by Gerry A Brown
Sat, Aug 09 2014, 9:18AM
Forum: Thermwood 3-Axis Machinery
Topic: cuts the wrong size
Replies: 8
Views: 4636

Re: cuts the wrong size

Hi,

I have been away from the shop so am a bit late responding.

Brad thanks I will try that. I have not tested any of the suggested mods yet but will post back with results when I have had a chance to do so.

Thanks,
Gerry
by Gerry A Brown
Thu, Aug 07 2014, 4:05PM
Forum: Thermwood 3-Axis Machinery
Topic: cuts the wrong size
Replies: 8
Views: 4636

Re: cuts the wrong size

Hi Scott,
I'll give all your suggestions a try keep you posted on the results.

Thanks,
Gerry
by Gerry A Brown
Thu, Aug 07 2014, 2:19PM
Forum: Thermwood 3-Axis Machinery
Topic: cuts the wrong size
Replies: 8
Views: 4636

Re: cuts the wrong size

Hello Scott, I did a few test cuts 1. a interpolated hole drawn at 1.05" cuts at 1.025" with .5" cutter 2. a slot drawn at .375 wide cuts at .3615" with .25" cutter 3. a slot drawn at .25" wide cuts at .247" with .25" cutter This is with the G07F5 in. I have a...
by Gerry A Brown
Thu, Aug 07 2014, 10:20AM
Forum: Thermwood 3-Axis Machinery
Topic: cuts the wrong size
Replies: 8
Views: 4636

Re: cuts the wrong size

Hi Scott,

I will give that a try.

Thanks,
Gerry
by Gerry A Brown
Thu, Aug 07 2014, 8:32AM
Forum: Thermwood 3-Axis Machinery
Topic: cuts the wrong size
Replies: 8
Views: 4636

cuts the wrong size

Hi Everyone, I am doing a job for a customer that has prepared the files with Aspire. The files require slots & holes cut to an exact size and I find the sizes are not coming out correctly. Interpolated holes are under size by .005" to .01" and the same with the slots. Is there a calib...
by Gerry A Brown
Tue, Jul 15 2014, 10:20AM
Forum: Thermwood 3-Axis Machinery
Topic: KD fasteners and tooling
Replies: 16
Views: 12167

Re: KD fasteners and tooling

Hi,

It looks like only the black one has been discontinued.

Thanks for that Forrest,
Gerry
by Gerry A Brown
Tue, Jul 15 2014, 7:59AM
Forum: Thermwood 3-Axis Machinery
Topic: KD fasteners and tooling
Replies: 16
Views: 12167

Re: KD fasteners and tooling

Hi Josh, We have used them in the past but I just looked for the part online & I see the flush version in 16mm has been discontinued. I guess I will need to find an alternative for the 16mm. I'll give the minifix a look. We mostly use them on 19mm lock dado closet parts so it is not something I ...

Go to advanced search