Search found 97 matches

by mohan kommineni
Thu, May 17 2012, 6:32PM
Forum: Thermwood 3-Axis Machinery
Topic: PROGRAM ERROR!!!!! INTERCEPT CALCULATION FAILED
Replies: 11
Views: 1954

Re: PROGRAM ERROR!!!!! INTERCEPT CALCULATION FAILED

Mohan, it looks like a Thermwood Software update may fix this problem, to be sure we need to run your program with your current version of software. Can you verify your version of Thermwood Control Software on your router..We will run with your current version and see if we get the same error as yo...
by mohan kommineni
Wed, May 16 2012, 6:53PM
Forum: Thermwood 3-Axis Machinery
Topic: PROGRAM ERROR!!!!! INTERCEPT CALCULATION FAILED
Replies: 11
Views: 1954

Re: PROGRAM ERROR!!!!! INTERCEPT CALCULATION FAILED

Hello ALL

I have sent all the information to thermwood and havent heard back so far please update

to me it looks like a serious bugggggggggg!!!!!!!!!!!!!!!!!

please update the status

Thanks
Mohan
by mohan kommineni
Fri, May 11 2012, 1:27AM
Forum: Thermwood 3-Axis Machinery
Topic: PROGRAM ERROR!!!!! INTERCEPT CALCULATION FAILED
Replies: 11
Views: 1954

PROGRAM ERROR!!!!! INTERCEPT CALCULATION FAILED

Hello all we are doing this job and facing this issue error screen shot isattached and the machine stalls then have to estop to home and have got few more same codes on the same program whaich are same issue too (program attached ) and pocket is not being cleaned there are steps leftover and manchin...
by mohan kommineni
Sun, May 06 2012, 7:05PM
Forum: Thermwood 3-Axis Machinery
Topic: Control RAM
Replies: 9
Views: 1934

Re: Control RAM

Try not to mix RAM types and brands if you can avoid it. RAM is cheap as these days. As long as you are not going to overclock or change voltages (you aren't) then just grab some mid price RAM. I would think for the controller you are not going to see much improvent of having more than 2x1GB sticks...
by mohan kommineni
Sun, May 06 2012, 6:59PM
Forum: Thermwood 3-Axis Machinery
Topic: CN 5.71 RAMP IN area not being cleaned out
Replies: 8
Views: 1364

Re: CN 5.71 RAMP IN area not being cleaned out

I was able to reproduce the issue now that I have seen the code you produced. When we tested the issue here, we were testing on version 7 and higher THM software. After seeing your code, I wrote the code for version 6 THM software and was able to reproduce the error. I have informed our software en...
by mohan kommineni
Thu, May 03 2012, 7:01PM
Forum: Thermwood 3-Axis Machinery
Topic: CN 5.71 RAMP IN area not being cleaned out
Replies: 8
Views: 1364

Re: CN 5.71 RAMP IN area not being cleaned out

Mohan, I did test this the first time you sent me the file and I was not able to reproduce the issue as I stated in the email. Who did you send the files to the second time? If you have this happen again, send the CNC file along with the export to program@thermwood.com and someone will look into it...
by mohan kommineni
Wed, May 02 2012, 7:44PM
Forum: Thermwood 3-Axis Machinery
Topic: CN 5.71 RAMP IN area not being cleaned out
Replies: 8
Views: 1364

Re: CN 5.71 RAMP IN area not being cleaned out

hello all
i have emailed the required files twice infact to two different persons and dont see any response so far is it a bug or technicians are too busy to analyse the issue

Thanks
Mohan
by mohan kommineni
Tue, Apr 17 2012, 8:33PM
Forum: Thermwood 3-Axis Machinery
Topic: Turning off vacume pumps
Replies: 6
Views: 1387

Re: Turning off vacume pumps

Hello Neville we had the same issue untill we got our remote switches installed on the controller itself and there is a provision on the controller to install the swicthes we have CS 45 and we have two pumps VLTF 250 & VLTF400 some times we use both and some times only one depends on the job siz...
by mohan kommineni
Tue, Apr 17 2012, 8:22PM
Forum: Thermwood 3-Axis Machinery
Topic: Control RAM
Replies: 9
Views: 1934

Re: Control RAM

Hi Kerry, You can add the ram to your control without any issues. It wont void any warranties for the machine. You can contact me in the service dept. if you need anything or have any questions. Thanks Hello Carl just want to know will there be any big difference on the ballastix ram and a standard...
by mohan kommineni
Tue, Apr 17 2012, 8:11PM
Forum: Thermwood 3-Axis Machinery
Topic: CN 5.71 RAMP IN area not being cleaned out
Replies: 8
Views: 1364

CN 5.71 RAMP IN area not being cleaned out

Hello all we are facing serious problems as the frequency of scrap jobs have become more due to this ramp in step not being cleaned out in the first pass and when doing the second pass the job starts moving out as they are small when the cutter touches the ramp in area not only that piece but also t...
by mohan kommineni
Wed, Apr 11 2012, 6:38PM
Forum: Thermwood 3-Axis Machinery
Topic: CN:5.70 issue on waste board settings
Replies: 7
Views: 1409

Re: CN:5.70 issue on waste board settings

Not only should the waste board issue be addressed but also the cut through amount it would be nice to default these settings to all groups you are right scott. it would be better option to the user to select whether to have default cut through amount or have individual cut through amounts based on...
by mohan kommineni
Mon, Apr 09 2012, 6:33PM
Forum: Thermwood 3-Axis Machinery
Topic: CN:5.70 issue on waste board settings
Replies: 7
Views: 1409

Re: CN:5.70 issue on waste board settings

Hello Daniel Thanks for the hint. just want to know why was this change has been done in the (CN ADDING INDIVIDUAL GROUP WASTE BOARD THICKNESS) is this some one has requested for or just as the part of software upgrades. the only issue is just imagine we have 44 groups and and have resurfaced the sp...
by mohan kommineni
Wed, Apr 04 2012, 7:36PM
Forum: Thermwood 3-Axis Machinery
Topic: CN:5.70 issue on waste board settings
Replies: 7
Views: 1409

CN:5.70 issue on waste board settings

Hello all we have just updated both the ecabinets systems and the control nesting software on the machine and now when we try to cut a job the its not cutting it to the exact depth and figured out that it was due to a bigger waste board thickness set in the program and after checking the settings on...
by mohan kommineni
Mon, Apr 02 2012, 6:15PM
Forum: eCabinet Systems Software
Topic: Ecabinet6.0 update build 8 not working
Replies: 2
Views: 523

Re: Ecabinet6.0 update build 8 not working

Can you uninstall V6 Build 8, then reinstall it and see if it works? Hello Rick we have uninstalled the update infact on the same spot when it didnt work and after your message here in the forum we have tried to reinstall the same and the process was different and which is showing thnigs have chang...
by mohan kommineni
Sun, Apr 01 2012, 9:11PM
Forum: eCabinet Systems Software
Topic: Ecabinet6.0 update build 8 not working
Replies: 2
Views: 523

Ecabinet6.0 update build 8 not working

Hello all i have downloaded the latest version and it says build 8 on the file itself (after downloading on to desktop) and when running the processes it says it is build 7 and in the next step it says build 8 and in this step the installation finishes very quickly and once clicking finish we have t...

Go to advanced search