Newby

John Reeves · Post by **John Reeves** » Fri, Mar 09 2007, 9:33AM

I think that I have gone from a majestic soaring Eagle to a small round green thing.

DanEpps · Post by **DanEpps** » Fri, Mar 09 2007, 10:29AM

John Reeves wrote:I think that I have gone from a majestic soaring Eagle to a small round green thing.

Never, John, never!!!

David Norton · Post by **David Norton** » Fri, Mar 09 2007, 7:18PM

John, JMHO here. But if I were you I would read the posts of those that actually use this software to design. And there are many.

Yeah, this post will probably catch my trousers on fire, but what the hell.
It has been my experience that some here know how to use this software to design. And there are some that know how the software works.

Again seek the advice of those that design, there are many on this forum. If you require technical advice, again here are those that can help. JMHO!

greg youngken · Post by **greg youngken** » Fri, Mar 09 2007, 7:28PM

Hey David, at the risk of sounding dumb, what is JMHO?

Michael Yeargain · Post by **Michael Yeargain** » Fri, Mar 09 2007, 7:31PM

Yeah, this post will probably catch my trousers on fire, but what the hell.
It has been my experience that some here know how to use this software to design. And there are some that know how the software works.

Oooooh don't ya smell it.

John Reeves · Post by **John Reeves** » Fri, Mar 09 2007, 7:42PM

I spent some time this afternoon trying to get the hang of it but ended up using a piece of graph paper and a mechanical pencil. At least it is a mechanical pencil!

How do you change the dimensions of a part (display board that I defined but got the length wrong) once it has Been loaded, aligned and associated with the cabinet. I need to learn how to tweak the fit of a few pieces.

All help is appreciated.

Green Round Thing.

John

Perry Pravettone · Post by **Perry Pravettone** » Fri, Mar 09 2007, 7:50PM

greg youngken wrote:Hey David, at the risk of sounding dumb, what is JMHO?

Greg, I think it's Just my honest opinon

Perry

greg youngken · Post by **greg youngken** » Fri, Mar 09 2007, 7:59PM

There is an alignment tool in the cabinet editor for precise alignment of parts. It's the red arrow between a red dot and a blue dot at the pick tool buttons at the top of the screen. I'm not sure of changing size on a diplay panel, but I'm sure someone will come along who does. play with that alignment tool, it's the greatest...

greg youngken · Post by **greg youngken** » Fri, Mar 09 2007, 8:00PM

thank you Perry

John Reeves · Post by **John Reeves** » Fri, Mar 09 2007, 8:04PM

I have the alignment tool OK. I also found holding down the \"M\" shows you all of the potential alignment points (blue dots). Cool Tool.

greg youngken · Post by **greg youngken** » Fri, Mar 09 2007, 8:08PM

the more I think about it , I dont think you can change the size of that display panel without just recreating it the size you need

Michael Yeargain · Post by **Michael Yeargain** » Fri, Mar 09 2007, 8:58PM

You can change the part size through the part editor. But unconventional. The best way is to reload the part.

JMHO

David Norton · Post by **David Norton** » Sat, Mar 10 2007, 10:19AM

Greg, JMHO- Just My Humble Opinion!

Perry Pravettone · Post by **Perry Pravettone** » Sat, Mar 10 2007, 10:41AM

David Norton wrote:Greg, JMHO- Just My Humble Opinion!

Thank's for the correction David, I'll have to correct my daughter. I'm to old for those IM short cuts

Perry Pravettone

Thermwood / eCabinet Systems

Newby

Re:

Re:

Re: