Rta Fittings

Joe Murphy · Post by **Joe Murphy** » Wed, Sep 05 2007, 10:54AM

Is Ecabs set up for a specific manufacturers rta fitting right out of the gate?

I don't use these often so i don't know if there are standard sizes.

Thanks,
Joe

Todd Miller · Post by **Todd Miller** » Wed, Sep 05 2007, 12:43PM

Joe Murphy wrote:Is Ecabs set up for a specific manufacturers rta fitting right out of the gate?

I don't use these often so i don't know if there are standard sizes.

Thanks,
Joe

Joe,
We have one hole pattern associated to our default RTA fastener. If you have a specific hole pattern you would like to draw up, you can draw it up withing the Hardware hole editor. Then associate the new hole pattern to the hardware you have chosen.

Todd Miller · Post by **Todd Miller** » Wed, Sep 05 2007, 12:45PM

Joe Murphy wrote:Is Ecabs set up for a specific manufacturers rta fitting right out of the gate?

I don't use these often so i don't know if there are standard sizes.

Thanks,
Joe

Joe,
We have one hole pattern associated to our default RTA fastener. If you have a specific hole pattern you would like to draw up, you can draw it up withing the Hardware hole editor. Then associate the new hole pattern to the hardware you have chosen.

Note:Dimensions are supplied for the hardware we offer.

Post by **Jason Susnjara** » Wed, Sep 05 2007, 1:41PM

Hi Joe,

The kd fasteners that we have setup are ones from Hafele. I believe the part number from Hafele is: hf-26310705 It consists of a 19 or 20mm hole for the plastic piece (they also have steel) and a 5mm hole for the pin which can be purchased in different lengths. These are nice because all holes can be cut or drilled from the sheet side and does not require any horizontal holes to be drilled. Here is a link to our member store to see the plastic piece.

http://www.woodworkerswholesale.com/Haf ... 310705.htm

Hope this helps.

DanEpps · Post by **DanEpps** » Wed, Sep 05 2007, 2:14PM

Jason

What are these made from? Must be really good to justify the $434.23 each price tag

Post by **Jason Susnjara** » Wed, Sep 05 2007, 2:30PM

Hi Dan,

Made from Solid Gold

. eCommerce is looking into this and will get it fixed. Thanks for letting me know.

Joe Soto · Post by **Joe Soto** » Wed, Sep 05 2007, 3:15PM

But Dan, as a memeber you do save $87.00 ea.

Joe

DanEpps · Post by **DanEpps** » Wed, Sep 05 2007, 3:25PM

Joe Soto wrote:But Dan, as a memeber you do save $87.00 ea.
Joe

Now what to spend it on...

Brian Shannon · Post by **Brian Shannon** » Wed, Sep 05 2007, 4:43PM

Wheel Chocks!

DanEpps · Post by **DanEpps** » Wed, Sep 05 2007, 4:48PM

Brian Shannon wrote:Wheel Chocks!

Too late for that

but at least I'm about over all the stiffness and soreness. I'm driving my '27 Ford roadster about 3 hours tomorrow to a street rod show in Pigeon Forge TN. I was wondering whether I would feel like it but I'm finally okay to drive

I knew there was a real good reason that I didn't like KD/RTA, I just couldn't remember what it was. Now I know its the price!!!

Brian Shannon · Post by **Brian Shannon** » Wed, Sep 05 2007, 4:53PM

Sorry Dan. You set it up, I had to use it! 'Good to hear your O.K. and feeling better.

Brian

Mark Taylor · Post by **Mark Taylor** » Wed, Sep 05 2007, 11:02PM

Hey Dan...if you get this before leaving, please post a photo of your car - Ginny and I headed up to our cabin this weekend and would love to meet you...as well as see your car!

Mark

DanEpps · Post by **DanEpps** » Thu, Sep 06 2007, 6:07AM

Sure thing Mark, love to meet you two also. The first pic is with the top on and the second is without (and one of our critters). I have the top on right now but might remove it tomorrow if there is no sign of rain.

We'll be staying at the Creekstone Inn, one block off the parkway at traffic light #8.

James Newman · Post by **James Newman** » Thu, Sep 06 2007, 9:35AM

Hey Dan,

That's a nice looking roadster. Any pics from the front? What frame, susp., etc... are you using?

I just bought a '38 Chevy truck cab. Nice winter project.

Al Navas · Post by **Al Navas** » Thu, Sep 06 2007, 5:24PM

DanEpps wrote:...The first pic is with the top on and the second is without (and one of our critters)...

Beautiful car, Dan!

I recognize the critter on the passenger side, but not the one in the drivers's seat...

Did you do all the work yourself?

Al

Thermwood / eCabinet Systems

Rta Fittings

Rta Fittings

Re: Rta Fittings

Re: Rta Fittings

Re:

Re:

Re: