RAW SEGMENT

Michael Yeargain · Post by **Michael Yeargain** » Sun, Oct 28 2007, 10:01AM

Here is a corner cabinet and I can't get the right stile to 45 back into the cabinet.

The left side is how I want the cabinet, but the right side just won't cooperate.

DanEpps · Post by **DanEpps** » Sun, Oct 28 2007, 10:32AM

Mike

You have a profiled edge on the left stile but not on the right.

Michael Yeargain · Post by **Michael Yeargain** » Sun, Oct 28 2007, 10:33AM

correct Dan, I want a profile on the right just like the left.

For some reason I get a error. \"Error creating Raw segment\" when I attempt to profile the right stile with a 45

DanEpps · Post by **DanEpps** » Sun, Oct 28 2007, 10:49AM

Something weird about the right stile. When I take it into contour mode and \"create edges\", nothing shows but the edges are there.

When I try to profile the edge it appears to work but back in the cab editor, it is still square.

You might try removing the face frame and putting it back.

DanEpps · Post by **DanEpps** » Sun, Oct 28 2007, 10:56AM

DanEpps wrote:...You might try removing the face frame and putting it back.

Well, that didn't help. I also noticed that the left end was mitered but not the right end. I mitered it and still get the same result.

DanEpps · Post by **DanEpps** » Sun, Oct 28 2007, 11:05AM

I'm beginning to think it might have a bad tessellation factor in it...

Philip Shantz · Post by **Philip Shantz** » Sun, Oct 28 2007, 2:11PM

Michael
You of all people should know that with the new segment factoring a profile like that can only be done by readjusting the phasers in the Contour Mode:

Michael Rice · Post by **Michael Rice** » Sun, Oct 28 2007, 2:33PM

I had the same problem about a year ago trying to bevel the edge on a right stile of a corner cabinet. The left stile was no problem, but I couldn't make the cut on the right stile. I brought it up on the forum, but I guess it never got noticed by the programers. Obviously, still not working...

Mike

DanEpps · Post by **DanEpps** » Sun, Oct 28 2007, 2:46PM

I was able to bevel it on a square cabinet but not on the corner cabinet.

DanEpps · Post by **DanEpps** » Sun, Oct 28 2007, 3:21PM

Alright Mike Rice, you got me back to hacking away at this (you know how it is).

I found the workaround to profiling the right stile on a corner cabinet!

You have to profile from the opposite edge (left instead of right) and offset right the (width - thickness) of the board.

In this example I used 3/4 x 2 board stock. I profiled the LEFT edge with an \"upside down\" tool and offset it right 1 1/4\".

My brain hurts...can I take the rest of the day off now?

Michael Rice · Post by **Michael Rice** » Sun, Oct 28 2007, 4:04PM

You got it Dan......we'll even pay you for the rest of the day...you earned your wizard stripes today...

Now, if I can just remember how to do it next time...

Mike

DanEpps · Post by **DanEpps** » Sun, Oct 28 2007, 4:06PM

If you can remember...I'm hoping I can remember.

Michael Yeargain · Post by **Michael Yeargain** » Mon, Oct 29 2007, 2:33PM

I was afraid I was going to have to do that.

I hope this one gets noticed.

Thermwood / eCabinet Systems

RAW SEGMENT

RAW SEGMENT

Re: