Search found 222 matches

by tim lucas
Tue, Sep 15 2015, 4:50PM
Forum: eCabinet Systems Software
Topic: Rotate Geometry pattern
Replies: 2
Views: 1563

Re: Rotate Geometry pattern

Thanks Scott, that will work :D
by tim lucas
Mon, Sep 14 2015, 4:18PM
Forum: eCabinet Systems Software
Topic: Rotate Geometry pattern
Replies: 2
Views: 1563

Rotate Geometry pattern

I created a back with some geometry and saved it, now I want to apply the geometry to a stretcher but I need to rotate one of them.
Is it possible??
Capture 1.JPG

Capture 2.JPG
by tim lucas
Fri, Jul 31 2015, 9:38AM
Forum: eCabinet Systems Software
Topic: Countertop
Replies: 9
Views: 2819

Re: Countertop

Go back to top editor and delete that top, then create a new top, see what happens
by tim lucas
Fri, Jul 31 2015, 9:27AM
Forum: eCabinet Systems Software
Topic: Countertop
Replies: 9
Views: 2819

Re: Countertop

If you select the top you should be able to move it down.

The only way I can think it installed this way is if you have 2 base cabinets next to each other and they are not the same height, when you create the top it will ask you what height to install at.
by tim lucas
Fri, Jul 31 2015, 7:03AM
Forum: eCabinet Systems Software
Topic: Countertop
Replies: 9
Views: 2819

Re: Countertop

Check to make sure your cabinet is not setting a couple inches below the floor.
If your cabinet is associated to a wall, go to the wall view and select that cabinet.
Look at position on wall, make sure bottom is not a negative number.
Tim
by tim lucas
Mon, Jul 06 2015, 7:22PM
Forum: eCabinet Systems Software
Topic: How to determine exact material thickness used before
Replies: 4
Views: 1319

Re: How to determine exact material thickness used before

Load your TWD file in the link, nest it, then go into add sheet - there you can see the material and the thickness of what you used

Tim
by tim lucas
Sun, Jun 28 2015, 6:36AM
Forum: eCabinet Systems Software
Topic: Rendering - lights wash out one wall
Replies: 7
Views: 2405

Re: Rendering - lights wash out one wall

Thanks Kerry, that looks good and just having 2 lights makes it a lot less setup

Tim
by tim lucas
Fri, Jun 26 2015, 6:56PM
Forum: eCabinet Systems Software
Topic: Rendering - lights wash out one wall
Replies: 7
Views: 2405

Re: Rendering - lights wash out one wall

Thanks Scott,

Between you and Kerry I might just make some nice presentations

Kerry, I still have not separated the cabinet texture from the doors but I understand lots more now

here is what I have so far,
Joel 3a.jpg

Joel 3b.jpg

Joel 3c.jpg

Joel 3d.jpg


Thanks again
Tim
by tim lucas
Fri, Jun 26 2015, 2:45PM
Forum: eCabinet Systems Software
Topic: Rendering - lights wash out one wall
Replies: 7
Views: 2405

Re: Rendering - lights wash out one wall

Hi Kerry, Thanks, I had not thought about the shine and slightly different textures, will give it a try. Any tips on rendering the lights in wall cabinets with glass doors? This job washout really looked different because one wall was way worse than the other. Thanks Tim the job file is over 7m zipp...
by tim lucas
Fri, Jun 26 2015, 12:44PM
Forum: eCabinet Systems Software
Topic: Rendering - lights wash out one wall
Replies: 7
Views: 2405

Rendering - lights wash out one wall

Having a problem with the lights washing out one wall but not the other Joel 3a.jpg Scott I am emailing this file to you - its the same kitchen as the countertop but with lights added if you could take a look when you have time, the stove wall keeps washing out while the sink wall is dark. I have so...
by tim lucas
Fri, Jun 26 2015, 6:15AM
Forum: eCabinet Systems Software
Topic: Countertop fillet
Replies: 2
Views: 925

Re: Countertop fillet

Hi Scott,

Emailed the job to you this morning

Thanks
Tim
by tim lucas
Thu, Jun 25 2015, 5:53AM
Forum: eCabinet Systems Software
Topic: Countertop fillet
Replies: 2
Views: 925

Countertop fillet

Trying to fillet a corner this morning and it wont select the long front edge, it will select the short edge in front of the angle base. Want to fillet the left front corner. I did double check the edge to make sure it is a front edge, selects left edge ok.
Tim
Capture.PNG
Capture.PNG (3.64 KiB) Viewed 925 times
by tim lucas
Wed, Jun 17 2015, 8:09PM
Forum: eCabinet Systems Software
Topic: placing cabinets back to back
Replies: 4
Views: 1296

Re: placing cabinets back to back

For islands I find it better to create an assembly in cabinet editor, bring in one cabinet got to top view move cabinet off target bring in another cabinet, rotate one cabinet 180 then select both cabinets, use item alignment to align the backs to zero - save as an assembly then when you place your ...
by tim lucas
Tue, Jun 09 2015, 8:09PM
Forum: eCabinet Systems Software
Topic: Error in contour editor
Replies: 2
Views: 968

Re: Error in contour editor

It seems to be only the bottom right corner, but if you connect through the lines all is well.
by tim lucas
Fri, Jun 05 2015, 9:26PM
Forum: eCabinet Systems Software
Topic: Default construction settings.
Replies: 1
Views: 789

Re: Default construction settings.

The idea is to create your own cabinet library. Take a wall cabinet say 2430 set all the setting the way you build, save it, resize it to say 3030, save it, resize it ....... soon you have a library of cabinets the way you build them.

Go to advanced search