KD/RTA Back

Justin Friesen · Post by **Justin Friesen** » Tue, Mar 06 2007, 2:12PM

Hi everybody,
With the new version of 5.1 I have had an opperation change. We use KD/RTA's in our back. We put the to the back of the cabinet to be hidden. Now in the new version when we put the KD/RTA's to the back it becomes a flip opperation. Could anyone tell me why this has changed, if it were accidental or on purpose.

Forrest Chapman · Post by **Forrest Chapman** » Tue, Mar 06 2007, 2:50PM

Justin,

Is the material single sided perhaps?

Forrest

Justin D Melhiser · Post by **Justin D Melhiser** » Tue, Mar 06 2007, 4:28PM

Justin

Do you have any other cuts or operations ont he front of the back part of the cabinet? Like a blind dado shelf?

Justin Friesen · Post by **Justin Friesen** » Wed, Mar 07 2007, 11:16AM

Hi guys, I do not have any other cuts in my back just 3 KD/RTA holes on each side, nothing else. Forrest I am using 2 sided white mcp, no grain. This problem has just occured when we updated to v5.1. Thanks for your help guys.

Michael RA Greschuk · Wed, Mar 07 2007, 12:35PM

Hey Justin I took one of the the old cabinets we drew and nested it without issue at the machine with no flips on the back you might want to check your material and see if the single sided box is checked for your 16mm white MCP.

I'm running 5.1 in Ecabs and 5.13 rolling nest

Regards Mike

Justin Friesen · Post by **Justin Friesen** » Wed, Mar 07 2007, 1:09PM

Hey Mike, how are you. I have also taken an old cab that we have drawn and it worked fine too. But when i draw a new cab I am getting this error. Haven't changed anything with the material. I am running v5.19 rolling nest. I don't think this is the issue because when I nest it in e-cabs it shows a flip for the backs. Thanks for your response Mike, hope to hear back from you soon.

Michael RA Greschuk · Post by **Michael RA Greschuk** » Wed, Mar 07 2007, 1:28PM

Hey Justin I'm doing OK I guess weathers nice today +15 and sunny I also tried drawing a new cab without any trouble the only thing I can suggest is roll back rolling nest and see if that makes adiffrence and or create anew hole pattern for your rta could be the dreaded metric issue again I'll play around with it at home tonight and see if I can come up up with that issue! is it showing flip on your desktop or just at rolling nest?give my greetings to everyone there

Scott G Vaal · Post by **Scott G Vaal** » Wed, Mar 07 2007, 1:40PM

Justin,

Please post the cabinet that you are having this issue with. I will take a look at it and see if I can reproduce it.

Justin Friesen · Post by **Justin Friesen** » Wed, Mar 07 2007, 7:33PM

Thanks for looking into this Scott. It's weird because I have never had this problem with any other version of e-cabs, just v5.1

Scott G Vaal · Post by **Scott G Vaal** » Thu, Mar 08 2007, 9:43AM

Justin,

This is the same issue that I discussed in a post from Thom Davies http://www.thermwood.com/forums/viewtopic.php?t=5281 . Even though you are using both a post hole and a cam hole with the KD/RTA, it has the same problem because your cam hole does not break through the edge of the part. If you will note, the edge of the part that has the cam hole is getting a small circle cut into it from the post hole. This is the issue that is causing the troubles. We will have an update out that resolves this very soon. Sorry for the inconvenience.

Justin Friesen · Post by **Justin Friesen** » Thu, Mar 08 2007, 12:23PM

Thank you so much. You guys are doing a great job and I couldn't be happier. Thanks again for all you have done.

Thermwood / eCabinet Systems

KD/RTA Back

KD/RTA Back