CN 5-39 problem

Nemanja Vujkovic · Post by **Nemanja Vujkovic** » Wed, Apr 09 2008, 8:06AM

I updated the CN this morning and ran in a problem. In front of every part, in the G-code, the CN throws a part information which is not completely in () which confuses the SuperControl. The error is invalid character in EIA block!!!

Todd Miller · Post by **Todd Miller** » Wed, Apr 09 2008, 9:28AM

Nemanja,
What kind of parts are you running?

When I post out with 5.39 I get lines like this.....

( Sheet: 1, Part: , Name: Front Toe, Material: 3/4 Generic)

Is a line like this giving you the error? If not post a the line or lines giving you the problem.

Nemanja Vujkovic · Post by **Nemanja Vujkovic** » Wed, Apr 09 2008, 9:34AM

Hi Tod!

I was running doors!
It looks like this

( Sheet: 1, Part: , Name: Right Hinge Double Door (Slab), Material: PL1_1SIDE)

Todd Miller · Post by **Todd Miller** » Wed, Apr 09 2008, 10:00AM

Nemanja Vujkovic wrote:Hi Tod!

I was running doors!
It looks like this

( Sheet: 1, Part: , Name: Right Hinge Double Door (Slab), Material: PL1_1SIDE)

Nemaja,
This is a known bug within Ecabinets having to do with the double (()) Parenthesis. This is carried over From Ecabs to CN thus causing the problem. This issue has been resolved in the latest build, which is going to be released very soon. The only work around at this time is to go into the NC code and delete the interior set of parenthesis.

The actual date for the release of the new update is close, but I do not know exactly when.

Nemanja Vujkovic · Post by **Nemanja Vujkovic** » Wed, Apr 09 2008, 10:47AM

I never had that problem before (and i started with the CNC when the CN was still in single digits), till now.
To fix this i ran the repair on 5-38 and it works just fine. The option of deleting the line of code is unproductive, especialy if there is over 100 doors to be cut!!!

Todd Miller · Post by **Todd Miller** » Wed, Apr 09 2008, 11:43AM

Nemanja Vujkovic wrote:I never had that problem before (and i started with the CNC when the CN was still in single digits), till now.
To fix this i ran the repair on 5-38 and it works just fine. The option of deleting the line of code is unproductive, especialy if there is over 100 doors to be cut!!!

Nemanja,
You're right! I have spoken with the programmers and they fixed this on the ecabinets end for the next build.

Todd Miller · Post by **Todd Miller** » Wed, Apr 09 2008, 2:56PM

Nemanja,
We should be releasing CN 5.40 today. It is not up yet, but I just tested it for this problem. This update should fix the issue you are having with the double parethesis when writing the code for doors. FYI

Nemanja Vujkovic · Post by **Nemanja Vujkovic** » Fri, Apr 11 2008, 6:06AM

Thank You Todd for the quick reply. I am looking forward to CN 5-40!!!

Todd Miller · Post by **Todd Miller** » Fri, Apr 11 2008, 7:30AM

Nemanja,
Here is a link to the CN update (V5.40).

http://downloads.thermwood.com/ControlNesting5-40.exe

Nemanja Vujkovic · Post by **Nemanja Vujkovic** » Tue, Apr 15 2008, 8:14AM

Thank you Todd!!!

Thermwood / eCabinet Systems

CN 5-39 problem

CN 5-39 problem

Re: CN 5-39 problem

Re: CN 5-39 problem

Re: CN 5-39 problem

Re: CN 5-39 problem

Re: CN 5-39 problem

Re: CN 5-39 problem

Re: CN 5-39 problem

Re: CN 5-39 problem

Re: CN 5-39 problem