end upper corner

Lorin Ylioja · Post by **Lorin Ylioja** » Sat, Nov 07 2009, 2:04PM

I am having trouble figuring out how to design an end corner cabinet with 2 doors angling to the center. I have built them before on the table saw but that isn't much help. here is an example http://www.kitchensonclearance.com/imag ... binets.jpg
Thank you
Lorin

George Davidson · Post by **George Davidson** » Mon, Nov 09 2009, 5:08PM

Out side Corner Cabinet

George Davidson · Post by **George Davidson** » Mon, Nov 09 2009, 5:38PM

Corner Cab.
DXF-Top
DXF-Bottom
Use Bottom DXF for sheld

Lorin Ylioja · Post by **Lorin Ylioja** » Tue, Nov 10 2009, 8:14AM

Thank you.
Lorin

Lorin Ylioja · Post by **Lorin Ylioja** » Sat, Dec 12 2009, 4:41PM

What do you do to create the front with angles like that?
I need to draw one up now as I got this Job and need to get my door order in and start cutting.
Thanks
Lorin

George Davidson · Post by **George Davidson** » Sat, Dec 12 2009, 5:51PM

Could you tell me more about what you are trying to do ?

Lorin Ylioja · Post by **Lorin Ylioja** » Sat, Dec 12 2009, 8:15PM

I am trying to build a frameless cabinet like the dxf file shown. I tried to use the ecabs one that you provided but I can't figure out how to remove the other 2 cabinets. I must be missing some trick, but I can't find the info in my Ecabs guide.
Thanks
Loirn

Gary Puckett · Post by **Gary Puckett** » Sat, Dec 12 2009, 8:27PM

Lorin,

Take the assembly to the cabinet editor, double click on the cabinet you want to delete then right click and chose delete. Repete for the other cabinet

Gary

Lorin Ylioja · Post by **Lorin Ylioja** » Sat, Dec 12 2009, 9:33PM

Thanks.
It sure is simple when you know what to do. I appreciate the help.
Lorin

Lorin Ylioja · Post by **Lorin Ylioja** » Sat, Dec 12 2009, 9:55PM

Now more problems. When I delete the doors and frames and try change materials and dimensions/insets it reverts to a square again. Do I have to change this in part editor??
Lorin

Lorin Ylioja · Post by **Lorin Ylioja** » Mon, Dec 14 2009, 9:39PM

Sitting here or the last few hours with ecabinets guide and still can't figure out how to make this cabinet. I can take a frameless corner cabinet, change all the material to 5/8 but can't get the angled fronts on it.

Any ideas what I should do at this point?? I want to make a 12"wide by 12" deep with no face frames but with doors.

Lorin

Kenneth Rychlik · Post by **Kenneth Rychlik** » Mon, Dec 14 2009, 10:32PM

lorin,

Are you just doing the design for display purposes or do you need to cut it on your machine as well?

Also do you need a center wall in it?

Kenneth

Lorin Ylioja · Post by **Lorin Ylioja** » Mon, Dec 14 2009, 11:23PM

I need it to cut, as well as to get my door sizes for ordering. it is on the end of a run of 12" deep by 40" tall uppers. All it needs is a left side and a back as well as 3 shelves. the doors will cover the front.
Thank you
Lorin

Kenneth Rychlik · Post by **Kenneth Rychlik** » Tue, Dec 15 2009, 12:53AM

Lorin, I am having trouble making it work too. I took a normal upper frameless cabinet and resized it to 12 inches wide. Next I deleted one side. Then highlight the top and take it to the part editor. Go to contour mode in part editor and you can draw the geometry there. Then get back out of contour mode into regular part editor and your geometry will still be there. Select your geometry and right click to open the option box. Select cut pocet using closed contoru and select cut through.
This will cut out whatever geometry you have selected.

Now for my trouble with it.

I can't seem to make my geometry into a closed coutour. It will not cut anything unless it is closed.

If someone will chime in and fill me in on how make the lines into a closed contour I think I can get you there.

Then you will have to take the bottom, top, and all shelves to make the same cuts on them.

As for sizing of the doors, it would be faster to lay it out on the workbench in full scale. lol

Kenneth

George Davidson · Post by **George Davidson** » Tue, Dec 15 2009, 8:52AM

Here is my corner frameless cabinet
In a Zip file with 2-DXF Top and Deck

Thermwood / eCabinet Systems

end upper corner

end upper corner

Re: end upper corner

Re: end upper corner

Re: end upper corner

Re: end upper corner

Re: end upper corner

Re: end upper corner

Re: end upper corner

Re: end upper corner

Re: end upper corner

Re: end upper corner

Re: end upper corner

Re: end upper corner

Re: end upper corner

Re: end upper corner