Search found 45 matches

by Wayne Adelkopf
Sun, Dec 01 2013, 5:28AM
Forum: Thermwood 3-Axis Machinery
Topic: Locating pins
Replies: 5
Views: 1884

Re: Locating pins

Awesome setup Dave. Where did you get the threaded shafts from?
by Wayne Adelkopf
Tue, Jul 09 2013, 10:39AM
Forum: Thermwood 3-Axis Machinery
Topic: Cut3D Post Processor
Replies: 1
Views: 1103

Re: Cut3D Post Processor

This works with Cut3D
You have to remove line 77 which has command to list tools
Save as *.pp and copy and paste into PostP folder of cut3D

viewtopic.php?f=7&t=13164&p=69489&hilit=vcarve#p69489
by Wayne Adelkopf
Mon, Jul 08 2013, 4:47PM
Forum: Thermwood 3-Axis Machinery
Topic: Cut3D Post Processor
Replies: 1
Views: 1103

Cut3D Post Processor

Does anyone have a post processor for Cut3D?
by Wayne Adelkopf
Sun, Apr 28 2013, 8:58AM
Forum: Thermwood 3-Axis Machinery
Topic: Shaker doors
Replies: 1
Views: 1691

Shaker doors

I am looking to efficiently cut shaker door frames with eCabs and control nesting. My rail size is 2-1/4" and the rabbet is 3/8" wide by 1/2" deep in 3/4" MDF. Does anyone have the silver bullet?
by Wayne Adelkopf
Tue, Jan 08 2013, 4:46PM
Forum: eCabinet Systems Software
Topic: Beaded face Frames
Replies: 2
Views: 1512

Re: Beaded face Frames

Try these. Use the bead tool for edge profile on stiles and rails. The cabinet doors and drawers are .75" inset.
by Wayne Adelkopf
Wed, Dec 12 2012, 4:53AM
Forum: eCabinet Systems Software
Topic: Closet suspension rails
Replies: 2
Views: 1804

Re: Closet suspension rails

The notch is 4" so that you can install the cabinet on the rail without a fight.
by Wayne Adelkopf
Mon, Nov 19 2012, 9:24PM
Forum: eCabinet Systems Software
Topic: Some suggestions for future updates
Replies: 7
Views: 1807

Re: Some suggestions for future updates

3) Create a cabinet with only the back. Have the back flush with all sides. Save it as "AAA_Display panel" so it is easy to find in your library. IE. a 20"x20" cabinet would leave you with just the back at 20"x20". You can change the size after you load it. This will al...
by Wayne Adelkopf
Sat, Nov 03 2012, 10:19AM
Forum: eCabinet Systems Software
Topic: Slot Slide Settings
Replies: 4
Views: 1178

Re: Slot Slide Settings

This is a part of the youbuildit furniture construction.
by Wayne Adelkopf
Tue, Oct 09 2012, 3:32AM
Forum: eCabinet Systems Software
Topic: Importing .DXF in Contour mgr
Replies: 4
Views: 1039

Re: Importing .DXF in Contour mgr

Thanks Rick.
by Wayne Adelkopf
Sat, Oct 06 2012, 11:30AM
Forum: eCabinet Systems Software
Topic: Importing .DXF in Contour mgr
Replies: 4
Views: 1039

Importing .DXF in Contour mgr

When I go to open .DXF files into Contour Mgr., I get the following error;
"The unregistered version is for evaluation only
Purchase at www.cadsofttools.com.

Has anyone encountered this? What is the solution?
by Wayne Adelkopf
Mon, Aug 06 2012, 11:08AM
Forum: eCabinet Systems Software
Topic: New PC
Replies: 3
Views: 886

Re: New PC

Thanks Rick:
I'm looking to see Manufacturer/model/specs others are going with...
by Wayne Adelkopf
Mon, Aug 06 2012, 10:21AM
Forum: eCabinet Systems Software
Topic: New PC
Replies: 3
Views: 886

New PC

Looking at buying a new PC and wanted to see what eCab folks are using.
by Wayne Adelkopf
Wed, Jul 25 2012, 12:13PM
Forum: Design Sharing
Topic: MDF door with X
Replies: 0
Views: 4029

MDF door with X

This is an MDF door that is the back of a cabinet. The back is set flush, 1/16" inset on top, deck, L&R sides. There is no top, deck or sides on this cabinet. This allows the door to be 1/8" less than the cabinet size L & W. The pattern is constrained to give 2-3/8" stiles and...
by Wayne Adelkopf
Mon, Apr 09 2012, 4:11PM
Forum: eCabinet Systems Software
Topic: Barb Dado
Replies: 3
Views: 897

Re: Barb Dado

Do not use with Particle core :wall: . Works okay with veneer core. Works best with MDF core. Overall, the joints hold secure but they are not as tight as can be achieved with screws. The application is nice when you have a finished end.

Go to advanced search