Crown on upper corners

Jean G Voyer · Post by **Jean G Voyer** » Fri, May 16 2008, 9:24AM

I create my crown for the uppers by using the top part of a cabinet. For the 90° corner the front crown will show in the cabinet editor but not in the custom layout.
I will try to attach the job. Didn't work.

Kerry Fullington · Post by **Kerry Fullington** » Fri, May 16 2008, 9:46AM

Jean,

If you are not placing the crown using the molding editor, make sure you associate the crown to the cabinet before returning it to custom layout.

Kerry

Jean G Voyer · Post by **Jean G Voyer** » Fri, May 16 2008, 11:02AM

Kerry,

I am placing the crown with the molding editor.

Jean G Voyer · Post by **Jean G Voyer** » Fri, May 16 2008, 11:11AM

Here is an example.
Then take the cabinet in the cabinet editor.
If it behaves like it does here you shouldn't have the front molding in the layout but you will have it in the cab editor.

Karin Sasse · Post by **Karin Sasse** » Sat, May 17 2008, 2:03AM

Hi Jean

I tried your cabinet and I cant see your molding in the room either, by the way I like the way you do your moldings. I took your cabinet and placed the moldings my way and they dont show up either. It must be a problem with corner cabs.

Thanks Fred

Rick Palechuk · Post by **Rick Palechuk** » Sat, May 17 2008, 10:03AM

Hey Jean, I did the crown on a corner cab your way and placed it in a room and it worked. Did you associate the front crown to the cab?

Jean G Voyer · Post by **Jean G Voyer** » Sat, May 17 2008, 10:15AM

Rick,

It won't let me associate the crown to anything. I am pretty sure it's a bug. I tried all sort of things. There must be something that you have done different than me.
I have been doing my crown like that for a long time and I never had any problem until 5.2.

Jean G Voyer · Post by **Jean G Voyer** » Sat, May 17 2008, 10:18AM

I can see what you have done. I think you have added the front piece separately. I am trying to use the molding editor.

Joe Dusel · Post by **Joe Dusel** » Sat, May 17 2008, 11:41AM

It's a bug for sure. If you are in the Cabinet Editor the molding shows. If you place the corner cabinet into a room the molding is missing from the front of the cabinet, but it shows on the sides.

Joe

Jean G Voyer · Post by **Jean G Voyer** » Sat, May 17 2008, 11:52AM

Thanks Joe & Karin. Then I feel I am not dreaming.
Sorry Rick but I know you are trying to help. I'll see you in the valley sometimes when I go to renew my supply of wine.

Rick Palechuk · Post by **Rick Palechuk** » Sat, May 17 2008, 2:27PM

The reason I placed the crown after is that I did a negative inset on the top. The crown would only follow the front without inset.

Rick Palechuk · Post by **Rick Palechuk** » Sat, May 17 2008, 2:33PM

I see what I should have done was just make the cab deeper by the amount of my inset. Sometimes thing are right in front of your nose and you don't even see them.

Walker T Scott · Post by **Walker T Scott** » Mon, May 19 2008, 7:00AM

I’ve listed this for the programmers.
Thanks

Thermwood / eCabinet Systems

Crown on upper corners

Crown on upper corners

Re: Crown on upper corners

Re: Crown on upper corners

Re: Crown on upper corners

Re: Crown on upper corners

Re: Crown on upper corners

Re: Crown on upper corners

Re: Crown on upper corners

Re: Crown on upper corners

Re: Crown on upper corners

Re: Crown on upper corners

Re: Crown on upper corners

Re: Crown on upper corners