Face Frame won't go thicker than .75 for sheet goods

BenRatt · Post by **BenRatt** » Sun, Oct 12 2008, 4:53PM

Why can't I select a sheet good material that is thicker than .75 for my face frames? I have some MDF that is .765. Any ideas?

Forrest Chapman · Post by **Forrest Chapman** » Sun, Oct 12 2008, 5:27PM

Ben,

Let me get this straight you are selecting sheet stock, thickness of .765, and then you cannot find the mdf in the list of available materials?

Forrest

BenRatt · Post by **BenRatt** » Sun, Oct 12 2008, 6:45PM

When I click on the frame thickness box, a bunch of different values appear for thickness less than .75, but no value greater than .75 shows up. BTW- when are you going to invite me over to your new shop?

Kerry Fullington · Post by **Kerry Fullington** » Mon, Oct 13 2008, 6:28AM

Benn,

eCabinets is probably seeing .765" as 3/4" I don't think eCabinets is accurate to 1/64" and .765 isn't quite 1/64" over 3/4".

I just tried it and if you enter a material of .766" it rounds up to 25/32"

Kerry

DanEpps · Post by **DanEpps** » Mon, Oct 13 2008, 6:45AM

I don't have any problem choosing a material that is .765" thick for face frame components. Double check your material and make certain it is actually defined with a .765" thickness.

: ff765.jpg (60.04 KiB) Viewed 9179 times

: ff765 Cutlist.jpg (103.29 KiB) Viewed 9179 times

Kerry Fullington · Post by **Kerry Fullington** » Mon, Oct 13 2008, 7:01AM

Dan,

This may be a deminsion Display problem. I use inches and fractions.
It works when I use inches and decimal.

Kerry

George Davidson · Post by **George Davidson** » Mon, Oct 13 2008, 7:16AM

Try .7656

DanEpps · Post by **DanEpps** » Mon, Oct 13 2008, 7:49AM

Kerry Fullington wrote:Dan,

This may be a deminsion Display problem. I use inches and fractions.
It works when I use inches and decimal.

Kerry

You may be on to something. When I change Dimension Display to use inches and fractions, I can select the .765" material but it is shown as 3/4". I saved a test cabinet using my .765" material with DD set to inches and fractions then reopened it and changed DD back to inches and decimal. It then showed the correct thickness in the cutlist where before it was 3/4".

Ben: What do you have set for Dimension Display in Settings and Preferences?

Forrest Chapman · Post by **Forrest Chapman** » Mon, Oct 13 2008, 8:16AM

Guys,

Because Ben and I own machines we use inches and decimals.

Ben, make sure you are selecting sheet goods first. Then your material should show up in all thickness. If it doesn't there is something wrong. I seem to remember something funky happening in FF to me once and I think turning the frame off and then changing the defaults from the main editor fixed it.

Ben, you can stop by any time just give me a heads up.

Thanks,
Forrest
864-226-5256 ext. 201 shop
864-844-1737 cell

BenRatt · Post by **BenRatt** » Mon, Oct 13 2008, 8:22AM

I use decimals. Here is a screen shot. I am using sheet goods. I'll try what you said Forrest.

Kerry Fullington · Post by **Kerry Fullington** » Mon, Oct 13 2008, 1:03PM

Ben,

Did you figure the problem out?

Thermwood / eCabinet Systems

Face Frame won't go thicker than .75 for sheet goods

Face Frame won't go thicker than .75 for sheet goods

Re: Face Frame won't go thicker than .75 for sheet goods

Re: Face Frame won't go thicker than .75 for sheet goods

Re: Face Frame won't go thicker than .75 for sheet goods

Re: Face Frame won't go thicker than .75 for sheet goods

Re: Face Frame won't go thicker than .75 for sheet goods

Re: Face Frame won't go thicker than .75 for sheet goods

Re: Face Frame won't go thicker than .75 for sheet goods

Re: Face Frame won't go thicker than .75 for sheet goods

Re: Face Frame won't go thicker than .75 for sheet goods

Re: Face Frame won't go thicker than .75 for sheet goods